 |
|
|
Elektronika.lt portalo forumas
Jūs esate neprisijungęs lankytojas. Norint dalyvauti diskusijose, būtina užsiregistruoti ir prisijungti prie forumo.
Prisijungę galėsite kurti naujas temas, atsakyti į kitų užduotus klausimus, balsuoti forumo apklausose.
Administracija pasilieka teisę pašalinti pasisakymus bei dalyvius,
kurie nesilaiko forumo taisyklių.
Pastebėjus nusižengimus, prašome pranešti.
Dabar yra 2024 10 11, 17:25. Visos datos yra GMT + 2 valandos.
|
|
|
 |
Forumas » Radioelektronika imtuvai » DEGEN DE1103
|
Jūs negalite rašyti naujų pranešimų į šį forumą
Jūs negalite atsakinėti į pranešimus šiame forume
Jūs negalite redaguoti savo pranešimų šiame forume
Jūs negalite ištrinti savo pranešimų šiame forume
Jūs negalite dalyvauti apklausose šiame forume
|
|
|
|
|
 |
DEGEN DE1103 |
 Parašytas: 2009 06 05, 20:22 |
  |
|
|
|
Aprašymas: http://www.radioscanner.ru/receivers/review/degen1103_eng.html
Modifikavimai:
"A engineer who ever work in DEGEN show a secret of DEGEN DE1103 on a
shortwave forum in china. The engineer want every swl who ever use
DEGEN DE1103 remember him. He made a small program in DE1103║╞s
software and it can let DE1103 auto scan from 000KHZ~29999KHZ
continue and not only scan in a sw band.
First, input 21951KHZ on sw. (the engineer║╞s worker number is 21951)
Second, At the same time press both ║╟BAND+║╠ Button and ║╟BAND-║╠
Button for a second then the radio will auto scan down until 000KHZ
and memorize one of frequency. If you want scan continue, use the
memory and scan."
It is possible to tune the 1103 receivers below 100kHz, and to
disconnect the internal ferrite rod antenna on MW + LW, by using
this simple procedure with the SCAN function.
Normally, a 'scan' will remain within the selected band, with
the tuning scale showing progress through the band. If you start
a scan from outside a band, the scan will become 'trapped' within
the next band that is reached. However, starting between 1 & 9kHz
above any band upper edge and scanning down, will bypass the 'band'
system, and will not switch to the ferrite rod in the range 1710 -
100kHz. The tuning will also continue below 100kHz.
So, select 1711 by direct entry:
[1] [7] [1] [1] [band+/AM]
and scan down: hold [BAND-] for 2 seconds.
As soon as the frequency is below 1710kHz you can stop the scan and
use the rotary control, or you can let the scan continue below 100kHz.
The antenna is now switched for the telescopic or external antenna.
I suggest you tune it down to zero and store this in preset 0, or store
99kHz in preset 99. Also store any frequencies for which you wish to
use the external antenna input. You can store any frequency with the
[SSB] mode 'on' for CW reception.
Once you tune above 1710 again, the system will revert to the normal
tuning range with the ferrite rod for MW + LW.
===========================================
There has been a suggestion that you must start the scan at 21951kHz
because that was the designer's employee number, but that story is
apocryphal!
http://www.radioscanner.ru/info/radio/degen2.php
http://mods.radioscanner.ru/degen/mod29/
Pagaliau gavau šį imtuvą ir labai juo džiaugiuosi 
p.s gal kas turit tokį patį? |
|
_________________
greitai ir pigiai nebūna gerai
pigiai ir gerai nebūna greitai
gerai ir greitai nebūna pigiai |
|
|
|
|
  |
|
|
|
 |
Google paieška forume |
|
|
|
Naujos temos forume |
|
|
FS25 Tractors
Farming Simulator 25 Mods,
FS25 Maps,
FS25 Trucks |
|
ETS2 Mods
ETS2 Trucks,
ETS2 Bus,
Euro Truck Simulator 2 Mods
|
|
FS22 Tractors
Farming Simulator 22 Mods,
FS22 Maps,
FS25 Mods |
|
VAT calculator
VAT number check,
What is VAT,
How much is VAT |
|
LEGO
Mänguköök,
mudelautod,
nukuvanker |
|
Thermal monocular
Thermal vision camera,
Night vision ar scope,
Night vision spotting scope |
|
FS25 Mods
FS25 Harvesters,
FS25 Tractors Mods,
FS25 Maps Mods |
|
Dantų protezavimas
All on 4 implantai,
Endodontija mikroskopu,
Dantų implantacija |
|
FS25 Mods
FS25 Maps,
FS25 Cheats,
FS25 Install Mods |
|
GTA 6 Weapons
GTA 6 Characters,
GTA 6 Map,
GTA 6 Vehicles |
|
FS25 Mods
Farming Simulator 25 Mods |
|
|
 |
